A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
We have stumbled on this post relating to A Step-by-Step Guide to Installing a Bathtub down the page on the net and concluded it made perfect sense to write about it with you in this article.
Setting up a tub isn't exactly rocket science, but it does need solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately tough job. If the old bathtub is conveniently accessible, the job can relocate immediately; if you need to open a wall surface to eliminate the old bathtub and also position the new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to consider utilizing one before you start. Opportunities are you might require a specialist plumber to make tube connections.
This article will certainly assist you set up a brand-new bathtub in your washroom if you have currently gotten a brand-new bathtub as well as don't need to change the setup of your previous water supply pipelines.
Your tools and material list need to consist of the following:
Getting ready for the Setup
To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain any water remaining in the system. The process of getting rid of the existing taps can be rather troublesome due to the limited accessibility that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Using both wooden boards under its feet, put the bathtub in the called for setting. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the bath tub up until the level reads level.
To mount taps, fit all-time low of the outermost flexible faucet port to the ideal supply pipeline by making a compression sign up with; then do the very same for the other tap.
Switch on the supply of water and check all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as also examine the overflow electrical outlet and the typical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been made use of at least once as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in position with the producer provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The former kind ought to be attached to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill the tub with water before securing, to enable the movement experienced when the tub is in usage. The sealant can split fairly early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the ceramic tiles using water-resistant or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very taken with A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed reading the new post. Kindly take the opportunity to share this post if you appreciated it. Thank-you for going through it.
Just a call away! Report this page